FORD SCORPIO

1985-1994 of release

Repair and operation of the car



Ford Skorpio
+ 1.1. Identification of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. Driveshaft and back bridge
+ 9. Steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tires
+ 13. Body
- 14. Electric equipment
   14.1. Technical characteristic
   14.2. Safety locks and relay
   14.3. Electronic control units
   14.4. System of the central blocking
   14.5. System of indexes of turns
   14.6. Fuel computer
   14.7. Additional control system
   + 14.8. Generator
   + 14.9. Starter
   + 14:10. Windshield screen wiper, knot of indexes and headlight
   14:11. Removal and installation of a combination of devices
   14:12. External and internal lighting
   + 14:13. Other electric equipment
   + 14:14. Electrical circuitries


9d8db598

14:12. External and internal lighting

MAIN HEADLIGHT

Replacement of a bulb of driving and passing beam

PERFORMANCE ORDER
1. To open a cowl.
2. To turn a back cover of a headlight counterclockwise and to remove it.
3. To disconnect the electric socket from a bulb and to squeeze pads (are specified by shooters) a spring clamp.
4. To take a bulb (it is specified by an arrow) from a headlight.
5. To establish a new bulb so that ledges of the holder of a bulb entered grooves of a reflector of a headlight and to fix by a spring clamp.

Prevention

It is strictly forbidden to concern a glass cylinder of a bulb barehanded. Otherwise it is necessary to wipe a bulb cylinder with alcohol.


6. To install the socket on a bulb and to close a back cover of a headlight.
7. To check adjustment of light of headlights.

Replacement of a bulb of dimensional light

PERFORMANCE ORDER
1. To open a cowl.
2. To turn a back cover of a headlight counterclockwise and to remove it.
3. To take from the lower part of a reflector the holder of a bulb together with a bulb.
4. To pull for a bulb (it is specified by an arrow) and to take from the holder.
5. To move a new bulb in the holder and to establish the holder in a reflector.
6. To close a back cover of a headlight.

Replacement of a bulb of the forward index of turns

PERFORMANCE ORDER
1. To open a cowl.
2. In a motor compartment to unhook the spring holding glass of a lamp of the index of turns and to take it outside.
3. To turn the holder of a bulb counterclockwise and to take him from a lamp.
4. To press a bulb in the holder and in this situation to turn counterclockwise and to take it.
5. To insert a new bulb in the holder (it is specified by an arrow).
6. To press a bulb against the stop and to turn in this situation clockwise.
7. The holder with a bulb to insert into a lamp and to turn clockwise before fixing.
8. To insert into place glass of a lamp and to fix it by a spring.

Adjustment of light of headlights

Screws of adjustment of light of headlights

1 – the screw of adjustment of light in the vertical plane,

2 – the screw of adjustment of light in the horizontal plane

Change of installation of light of the main headlights is carried out by turn of the screws located in a back part of headlights (available from a motor compartment).

In headlights for adjustment in the vertical plane the lower screw, and for adjustment serves in the horizontal plane – the top screw.

Entry conditions:

  – tires of wheels have to be pumped up up to the necessary size of pressure of air in them;
  – the car with a full tank of fuel has to be loaded only weighing 75 kg on sitting of the driver;
  – in front of the car it is necessary to press strongly several times for the corresponding placement of elastic elements of a suspension bracket

Adjustment of a ray of light of headlights

Scheme of adjustment of headlights

And – light border,
In – the center of a light stream,
With – a lighting zone passing beam,
D – interaxal distance of headlights,
N – height of installation of headlights,
About – a car axis,
X = 120 mm for the main headlights and X = 220 mm for fog lights.

PERFORMANCE ORDER
1. To install the car on a plain horizontal surface at distance of 10 meters from a vertical wall.
2. On a wall to put lines of a marking according to rice. Scheme of adjustment of headlights.
3. To turn on passing beam of headlights and to close one headlight improvised material and to make adjustment of a ray of light of the second headlight.
4. To repeat operation on adjustment for the second headlight.
5. As soon as possible to make adjustment of light of headlights on the special equipment.

Replacement of a bulb of an additional headlight

PERFORMANCE ORDER
1. To open a cowl.
2. To remove a plastic cover from the top part of a headlight, previously having released wire clips (shooter).
3. To squeeze and take aside two wire clamps.
4. To take a bulb and to disconnect the electric socket.
5. To connect the socket of a new bulb and to establish a bulb (it is specified by an arrow) so that ledges of the holder of a bulb entered headlight reflector grooves.

Prevention

It is strictly forbidden to concern a glass cylinder of a bulb barehanded. Otherwise it is necessary to wipe a bulb cylinder with alcohol.


6. To fix a bulb by two wire clamps.
7. To establish and record a plastic cover.
8. To check adjustment of light of headlights.

Replacement of a bulb of a forward fog light

Bulb of a forward fog light

And – screws of fastening of a headlight,

With – the headlight light adjustment screw

PERFORMANCE ORDER
1. To unscrew two screws from two parties of a headlight and to take a headlight from a nest.
2. From the back party of a headlight to squeeze a spring clamp of a bulb and to take it aside.
3. To take a bulb and to switch-off the electric socket.
4. To establish a new bulb so that ledges of the holder of a bulb entered grooves of a reflector of a headlight and to fix by a spring clamp.

Prevention

It is strictly forbidden to concern a glass cylinder of a bulb barehanded. Otherwise it is necessary to wipe a bulb cylinder with alcohol.


5. To connect the electric socket.
6. To establish a headlight in a nest and to fix by screws.
7. To check adjustment of light of headlights.

Prevention

Adjustment of light of a fog light in the vertical plane is made by rotation of the screw located in the top part of a headlight.


Replacement of a bulb of the side repeater of turns

PERFORMANCE ORDER
1. To turn glass of the repeater of turns clockwise and to take the repeater of turns from a body.
2. To turn glass of the repeater of turns counterclockwise in relation to the holder of a bulb and to remove it.
3. Having pulled for a bulb, to take it from the holder.
4. To establish a new bulb in the holder.
5. To establish glass of the repeater of turns on the holder and to record it turn clockwise.
6. To install the repeater of turns in a body and to record it turn counterclockwise.

BACK LAMP

Replacement of bulbs

Arrangement of bulbs on the holder

1 – bulb of the back index of turns (12V, 21W),

2 – bulb of fires of braking (12V, 21W),

3 – dimensional bulb (12V, 10W),

4 – back fog bulb (12V, 21W),

5 – bulb of a backing (12 V, 21 W)

Replacement of bulbs of a lamp of a backing is made from the luggage compartment.

PERFORMANCE ORDER
1. To uncover (shooters), closing lamps from the relevant party. On the right side it is necessary to switch-off the electric socket.
2. To squeeze in the direction to each other clamps and to take the holder of bulbs of a lamp.
3. For replacement of a faulty bulb to press a bulb in the holder and in this situation to turn it counterclockwise and to take from the holder.
4. To insert a new bulb in the holder, to press it against the stop and to turn in this situation clockwise.
5. To establish into place and to record the holder of bulbs.
6. To establish the cover closing lamps.

Removal of a back lamp

PERFORMANCE ORDER
Hatchback body
1. To uncover from luggage the compartment of a back lamp.
2. To unscrew six nuts (are specified by shooters) fastenings of a back lamp.
3. To take a lamp outside of the car and to remove the socket.
Body Sedan
4. To remove a luggage carrier upholstery from the required party.
5. To unscrew nuts (2) fastenings of a back lamp. To take a lamp outside of the car and to remove the socket (1).

Replacement of a bulb of illumination of registration plate

PERFORMANCE ORDER
1. To insert an edge of the thin screw-driver under rubber consolidation of a lamp and to press a clamp (1) of a plafond and to take a lamp from a bumper.
2. To turn the holder of a bulb counterclockwise and to take him.
3. Having pulled for a bulb, to take it from the holder.
4. To establish a new bulb in the holder.
5. To establish the holder of a bulb in a lamp and to turn against the stop clockwise.
6. To establish a lamp in a bumper before its accurate fixing.

Replacement of lighting lamps of salon

PERFORMANCE ORDER
To insert an edge of the thin screw-driver on the right side under the block of lighting and having pressed the screw-driver to take it from a nest. In case of removal of the lamp for reading to insert the screw-driver from below in a middle part of the block of lighting. To make replacement of lamps and to install the block into place. If necessary it is possible to draw in the contacts holding a bulb.

Replacement of lighting lamps of a mirror

PERFORMANCE ORDER
1. To insert an edge of the thin screw-driver on the right side under a frame of a mirror and, having pressed the screw-driver, to take a frame from a nest.
2. To make replacement of a bulb and to establish a frame into place. If necessary it is possible to draw in the contacts holding a bulb.

Replacement of bulbs of the alarm system of open doors, illumination of space for legs and luggage compartment

PERFORMANCE ORDER
1. To insert an edge of the thin screw-driver under a plafond of a bulb and, having pressed the screw-driver, to take a plafond from a nest.
2. To take out a bulb and to replace it (in the drawing – replacement of an alarm bulb of open doors).
3. To replace a bulb and to establish a plafond before its accurate fixing.

Removal and installation of a headlight and svetorasseivatel

PERFORMANCE ORDER
1. To open a cowl.
2. To remove a weight wire from the car.

Prevention

At the same time information in electronic memory devices is erased from memory.


3. To disconnect the electric socket close to a headlight. In the presence of the proofreader of light of headlights also to disconnect from it the electric socket.
4. To remove a lamp of the index of turn.
5. To remove the rubber laying located between a bumper and a headlight.
6. To remove the front grille fixed by two screws.
7. To unscrew top (it is specified by an arrow in the drawing on the right) and lower (it is specified by an arrow in the drawing at the left) bolts of fastening of a headlight.
8. To slightly unscrew a side nut (it is specified by an arrow) fastenings of a headlight and to take a headlight, having moved it forward and aside.
9. To remove all bulbs from a headlight.
10. Inserting into grooves from the back party of a headlight the screw-driver and turning it, to remove spring clips of fastening of glass.
11. To remove headlight glass together with sealing laying.

Replacement of the lighting lamp of switches

Replacement of lamps can be made after removal of the handle of the switch.

PERFORMANCE ORDER
1. To remove the handle for access to a lamp (it is specified by an arrow) the switch.
2. To replace a bulb.

Replacement of the lighting lamp of a ware box

PERFORMANCE ORDER
1. To open a ware box (the arrow specified an arrangement of the lighting lamp of a ware box).
2. To unscrew two screws and to take the block of the switch and a lamp.
3. To take a lamp from the block and to establish new.

Replacement of the lighting lamp of an ashtray

PERFORMANCE ORDER
1. Over an ashtray to remove a box or the radio receiver (the arrow specified an ashtray lighting lamp arrangement).
2. Through the opened opening to take the holder of a bulb, extending it outside, or the screw-driver carefully to separate it from a casing.

Replacement of a lamp of illumination of the panel of a heater

PERFORMANCE ORDER
1. To remove a dashboard fringing.
2. To remove the handle of management of a heater, having pulled it on itself.
3. By means of the screw-driver to remove the heater panel.
4. To take a bulb (it is specified by an arrow) from the holder.
5. To replace a bulb.

Replacement of a lamp of illumination of the selector of the automatic transmission

PERFORMANCE ORDER
1. To unscrew the selector handle.
2. To remove a selector casing.
3. To wring out two brackets of fastening of a scale of the selector and to remove a selector scale.
4. To unscrew four screws and to remove the directing plate.
5. To remove the holder and to replace a lamp (it is specified by an arrow) selector illuminations.

Replacement of a lamp of illumination of the switch of the alarm light system

PERFORMANCE ORDER
1. To remove the top casing of a steering column, previously having unscrewed three screws.
2. To check that the switch is in situation "Vykl" then to remove the switch button.
3. To take and insert a new lamp.
4. To install into place the button of the switch and the top casing of a steering column.

Replacement of a lamp of illumination of hours

If hours are determined in a combination of devices, replacement is made similar to replacement of control bulbs.

PERFORMANCE ORDER
1. In case of installation of hours with the top arrangement, for replacement of a bulb of illumination of hours it is necessary to remove the top console.
2. For removal of the top console to remove a plafond of illumination of salon and the handle of opening of the hatch, to unscrew two screws of fastening of a forward part of the console, to lower a forward part of the console down and to shift back.
3. For access to a lamp to remove a back cover of hours, previously having unscrewed two screws.
4. To replace a lamp (it is specified by an arrow) with bayonetny fastening.
5. To establish a back cover of hours and then the top console.