FORD SCORPIO

1985-1994 of release

Repair and operation of the car



Ford Skorpio
+ 1.1. Identification of the car
+ 2. Maintenance
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. Driveshaft and back bridge
+ 9. Steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tires
+ 13. Body
- 14. Electric equipment
   14.1. Technical characteristic
   14.2. Safety locks and relay
   14.3. Electronic control units
   14.4. System of the central blocking
   14.5. System of indexes of turns
   14.6. Fuel computer
   14.7. Additional control system
   + 14.8. Generator
   + 14.9. Starter
   + 14:10. Windshield screen wiper, knot of indexes and headlight
   14:11. Removal and installation of a combination of devices
   14:12. External and internal lighting
   - 14:13. Other electric equipment
      14.13.1. Removal and installation of switches, engines and sensors
      14.13.2. Additional control system
      14.13.3. Removal and installation of the radio receiver
      14.13.4. Removal and installation of loudspeakers
      14.13.5. System of the anticreeping alarm system
   + 14:14. Electrical circuitries


9d8db598

14:13. Other electric equipment

Replacement of the engine of the proofreader of light of headlights

The engine of the proofreader of light of headlights is installed from the back party of a headlight and fastens by means of a bayonetny clip.

PERFORMANCE ORDER
1. To remove the electric socket from the engine of the proofreader of light of headlights.
2. To press the proofreader's engine in the direction of a headlight and in this situation to turn the engine clockwise for a right headlight or counterclockwise for a left headlight.
3. Through an opening in the case of a headlight to press the lever of the fixing adjusting shaft and to take the proofreader's engine from a headlight.
4. Installation is made in the sequence, the return to removal.

Removal and installation of hours

PERFORMANCE ORDER
1. To remove the top console.
2. For removal of the top console to remove a plafond of illumination of salon and the handle of opening of the hatch, to unscrew two screws of fastening of a forward part of the console, to lower a forward part of the console down and to shift back.
3. To remove a back cover of hours, previously having unscrewed two screws.
4. To unscrew two screws of fastening and to take hours.
5. To install hours on the console.
6. To establish a back cover of hours and then the top console.

Removal and installation of the lighter

PERFORMANCE ORDER
1. To remove a weight wire from the accumulator.
Forward lighter
2. On models with the increased level of finishing of salon for access to the lighter to remove an overlay of the central console from the radio receiver.
3. On models with usual finishing of salon to remove the radio receiver.
4. To disconnect from the lighter of a wire and to take it from the highlighted ring.
Back lighter
5. To remove the handle of management of a heater.
6. To remove the panel of the back central console, previously having unscrewed two screws of fastening.
7. To disconnect from the lighter of a wire and to take it from the highlighted ring.
8. Installation is made in the sequence, the return to removal.

Removal and installation of a sound signal

Two sound signals are installed in the car. The sound signal of high-pitch tone is established to the right of a radiator and is available from a motor compartment. The low-frequency sound signal is established from below and to the left of a radiator and is available from below a motor compartment.

PERFORMANCE ORDER
1. To unscrew a fixing nut or a bolt and to remove the vibroextinguishing washer.
2. To remove electric sockets and to take a sound signal.
3. Installation is made in the sequence, the return to removal.

Removal and installation of the switch of a sound signal, contact rings and brushes

PERFORMANCE ORDER
1. To remove a weight wire from the accumulator.
2. Remove the central overlay of a steering wheel.
3. To unscrew three screws (are specified by shooters) fastenings of a bracket of the switch of a sound signal.
4. To remove the electric socket and to take a bracket of the switch of a sound signal.
5. To remove a steering wheel.
6. To unbend ears of fastening of contact rings to the lower part of a steering wheel, to disconnect from a bracket and to remove contact rings.
7. To remove the top and lower casings of a steering column.
8. To disconnect wires from brushes of a sound signal.
9. Being careful, to squeeze out the block of brushes the screw-driver inserted under bottom edge of the block.
10. Installation is made in the sequence, the return to removal.

Removal and installation of elements of a heater of seats

PERFORMANCE ORDER
1. To remove a seat.
2. To remove a seat upholstery.
3. To note the direction of an arrangement of a heating element, then to remove wire clips and the adhesive tape fixing an element to sitting.
4. To establish clips on a new element.
5. To establish a new heating element by the forward party to pillow foam rubber. To fix a heating element by wire clips and a tape. To check that the heating element caves in at the annex of loading to sitting.
6. To establish a sitting upholstery.
7. To establish sitting.
8. The regulator (shooter) has to be directed by the forward party to pillow foam rubber.

Removal and installation of contact group of the lock of ignition

PERFORMANCE ORDER
1. To remove a weight wire from the accumulator.
2. To remove the top and lower casings of a steering column, previously having unscrewed six screws of fastening.
3. To release contact group of the lock of ignition (shooter), having wrung out two fixing ears.
4. At installation to check that the cut in the center of contact group of the lock of ignition was made even to a ledge on the lock.
5. To connect contact group of the lock of ignition and to press it into place to a zashchelkivaniye of fixing ears.
6. To connect a weight wire to the accumulator and to check efficiency of contact group of the lock of ignition then to establish casings of a steering column.